Ammonium metatungstate decomposition temperature is the temperature of AMT coming out decomposition reaction; while in the actual production environment, ammonium metatungstate will have several different decomposition temperatures according to complete reaction or not. Decomposition temperature of a substance means the temperature at which the substance chemically decomposes, which the chemical decomposition caused by heat. The reaction is usually endothermic as heat is required to break chemical bonds in the compound undergoing decomposition. If decomposition is sufficiently exothermic, a positive feedback loop is created producing thermal runaway and possibly an explosion.

 

Ammonium metatungstate will produce different products at different decomposition temperatures. When the heat treatment temperature is 200~300°C, AMT will be removed of all crystal water and most of the ammonium ions; then phase transformation will occur at 300-350°C to generate metastable tungsten oxide species; when the heat treatment temperature rise to 500~550°C, a small amount of ammonium and bound water is still not broken down; and when the temperature rises to 600°C and above, ammonium metatungstate will completely decomposed into tungsten trioxide (WO₃); when the temperature raised to 700°C and held for 2 hours, mesoporous tungsten trioxide hollow balls will be obtained.

 

About ammonium metatungstate:

Ammonium metatungstate (AMT) is an important intermediate compound in tungsten wet smelting process, with the appearance of white or slightly yellow crystalline, the biggest solubility in all the tungsten compound, wherein the solubility will bigger than 300g WO₃/100ml H₂O at 25℃. The preparation methods of ammonium metatungstate are mainly Acid neutralization, Thermal separation, electrodialysis, solvent extraction and ion exchange method and the method depends on ammonium paratungstate (APT). AMT is the important raw material of tungsten compound (such as tungsten trioxide, blue tungsten oxide, tungsten hexachloride ect.); at the same time, it is usually used in industries of petroleum, chemical, ceramic, lubrication and so on; in addition, since the continually developing of electronics industry and the constantly mining of new material, AMT is also used in film substrate, capacitor and shielding ect. of semiconductor devices.

The detection methods of ammonium metatungstate are graphite furnace atomic absorption spectrometry (GFAAS), flame atomic absorption spectrometry (FAAS), inductively coupled plasma emission spectrum (ICP-MS) and coprecipitation separation - hydride atomic fluorescence spectrometry (i.e. coprecipitation separation - HG - AFS method.

 

Graphite furnace atomic absorption spectrometry (GFAAS) is the method absorbing and analyzing atoms by atomization with current heating in an atomization device which produced by graphite and to form shapes of tubes, cups and others. Since all atoms of sample are getting involved in the atomization, and the atomic concentration diluted in the flame gas has been avoided, then the analytical sensitivity has been greatly improved. While, when that method applied in detecting trace metal element, its property is better than many of other methods, and will be used in analysis of small amount samples and detect analysis of solid sample.

 

Detection equipments of ammonium metatungstate are atomization device, flame atomic absorption spectrometer, and inductively coupled plasma mass spectrometer ect..

1. Atomization device is a device for sample atomization of atomic absorption spectrometry, which is used in both graphite furnace atomic absorption spectrometry (GFAAS) and flame atomic absorption spectrometry (FAAS). It converts the sample to a free atomic vapor (ground state atom) to absorb the characteristic radiation, and to calculate the element to be measured. There are many kinds of atomizers, and they can be divided into two categories of fire stuffing atomizer and electrothermal atomizer in common. The former includes pre-mixed and full consumption type; the latter includes graphite furnace, carbon wire atomizer, carbon rod atomizer, graphite increase exhaust, and graphite probes ect.;

2. Inductively coupled plasma mass spectrometer consists of plasma torch (composed of three concentric quartz tube), high frequency generator (to produce high frequency current), induction coil, gas supply system and atomization system and other parts;

3. Flame atomic absorption spectrometer is composed of light source, atomization system, spectroscopic system and detection system. The principle is that the instrument emits light with the characteristic spectral line of the element to be measured from the light source, then when the sample vapor passes through, the light will be absorbed by the under measure ground state atom, and finally measured by the weakened degree of radiation characteristic spectrum of light.

Ammonium metatungstate spray drying tower belongs to the spray equipments of ammonium metatungstate production, which is the most widely used of liquid forming process and drying industry. Spray-drying tower is suitable for preparing powder, granular solid product from liquid raw material with forms of suspoemulsions, solution, emulsion, and paste. Thus, when the finished product particle size distribution, residual moisture content, bulk density and particle shape are in line with the precision standard, the spray drying tower is supposed to be an ideal drying process.

 

Principle of ammonium metatungstate spray drying tower is that the air goes into the top dryer’ air distributor after filtered and heated, then the hot air will uniformly go into the drying room in the spiral. AMT feed solution through the high-speed centrifugal atomizer (rotary) at the top of the tower to be sprayed into the extremely fine mist liquid beads AMT, and dried AMT will come into being in a very short time when it in contacts with the stream of hot air. Then, ammonium metatungstate is exported continuously from the bottom of the spray drying tower and the cyclone, and the exhaust gases are vented by the fan.

 

Extended reading:

Spray drying tower is the equipment which can be used in drying biological pesticide, medicine and food microorganism, with the max evaporation rate of 10 kg/h, max gas drying rate of 150 kg/h; the main function of a spray drying tower is to dry the materials in solution state in it and then discharge in form of solid. There are 6 properties of a spray drying tower which show bellows:

1. The fast drying speed within seconds to finish;

2. Suitable for the heat-sensitive materials;

3. Widely apply in most of products with very huge difference;

4. The outlet product has excellent dispersion, fluidity and solubility;

5. Sample producing process and easy to operate and control;

6. The part which in contact with material is using stainless steel to protect raw material not to be polluted and extend the service life of the equipment.