Tungsten carbide rods are mostly applied for drill bits, end mills, and reamers with sub-micron grain grade YG10X, for non-ferrous precision cutting and wood cutting with grade YG6X, and for fiberglass reinforced plastics, titanium alloys, hardened steel with ultra-fine grain grade YG8X, etc.



Tungsten Manufacturer & Supplier: Chinatungsten Online - http://www.tungsten-carbide.com.cn
Tel.: 86 592 5129696; Fax: 86 592 5129797
Email: sales@chinatungsten.com
Tungsten Picture Center: http://picture.chinatungsten.com
Tungsten Video Center: http://v.chinatungsten.com
Tungsten News & Tungsten Prices, 3G Version: http://3g.chinatungsten.com

1. Remove the tire from the vehicle. Apply tire lubricant to each of the carbide studs. For best results, purchase tire lubricant that is used to mount tires.

2. Grip the stud with a pair of pliers and twist as you pull.

3. Continue twisting and pulling each stud until all are removed.

4. Place the tire in a tank of water after all the studs are removed or spray completely around the tire with window cleaner. Watch for air bubbles that indicate a puncture.

5. Have the punctures repaired at a tire shop, if needed.

6. Rinse the tire to remove all of the lubricant and mount the tire back onto the vehicle.

7. Test the air pressure after the tire is mounted, and add or remove air to get the tire pressure into the recommended range.


Tungsten Manufacturer & Supplier: Chinatungsten Online - http://www.tungsten-carbide.com.cn
Tel.: 86 592 5129696; Fax: 86 592 5129797
Email: sales@chinatungsten.com
Tungsten Picture Center: http://picture.chinatungsten.com
Tungsten Video Center: http://v.chinatungsten.com
Tungsten News & Tungsten Prices, 3G Version: http://3g.chinatungsten.com
 

Tungsten carbide studs are commonly inserted in snow tires in areas with a lot of snowy or icy weather. Tire studs increase traction in bad road conditions caused by the bad weather.

When the bad weather has passed and the tires are driven on the road, the tungsten carbide studs are very noisy and cause damage to road surfaces. Thankfully, tungsten carbide tire studs are removable so that snow tires can continue to be used without dealing with the noise or damaging the highways.


Tungsten Manufacturer & Supplier: Chinatungsten Online - http://www.tungsten-carbide.com.cn
Tel.: 86 592 5129696; Fax: 86 592 5129797
Email: sales@chinatungsten.com
Tungsten Picture Center: http://picture.chinatungsten.com
Tungsten Video Center: http://v.chinatungsten.com
Tungsten News & Tungsten Prices, 3G Version: http://3g.chinatungsten.com
 

The only way to remove a tungsten carbide ring in case of emergency is to remove the finger. But the usual method of using a pair of metal cutters on the ring won't work. What you need is a strong grip and a pair of the proper pliers.

1. Take the vise-grip pliers and carefully begin to squeeze the tungsten carbide ring. Steadily adjust the pressure on the side of the vise until you hear the ring crack.

2. Rotate the ring (or the pliers if the ring is stuck too tightly to turn) a third of the way and repeat the previous step. Continue to squeeze the ring until you hear it crack in a different place.

3. Continue cracking the tungsten carbide until it breaks entirely. The ring should shatter, leaving the finger intact.

Tips & Warnings
If possible, allow emergency or medical personnel to crack a tungsten carbide ring. But if you have to do it yourself, be very careful to ramp up the pressure in increments so that you don't accidentally clamp the person's finger with the vise grips.


Tungsten Manufacturer & Supplier: Chinatungsten Online - http://www.tungsten-carbide.com.cn
Tel.: 86 592 5129696; Fax: 86 592 5129797
Email: sales@chinatungsten.com
Tungsten Picture Center: http://picture.chinatungsten.com
Tungsten Video Center: http://v.chinatungsten.com
Tungsten News & Tungsten Prices, 3G Version: http://3g.chinatungsten.com